How2NewGlass2

How2NewGlass2

Surface Preparation

White, Cream, Ivory or Off White surfaces should be thoroughly washed with NewGlass2 PreTreat or a mildly abrasive cleanser. The surface should be free of dirt, grease, and stains. Any oxidation remaining on a light colored surface after a thorough cleaning will be absorbed into the background when NewGlass2 is applied.

Darker colored surfaces should be thoroughly washed with NewGlass2 PreTreat or a mildly abrasive cleanser. The surface should be free of dirt, grease, and stains. Any oxidation remaining on a colored surface after a thorough cleaning should be removed by wet sanding with 800 to 1000 grit wet / dry sandpaper. This sandpaper can be wrapped around a sponge and used with water to lightly sand away oxidation. The surface should be cleaned again and should be uniform in color before applying NewGlass2.

NewGlass2 PreTreat can be mixed 3 parts water to 1 part PreTreat. It should be applied to a wet 4' by 6' area and scrubbed with the supplied scrubber. If PreTreat is being used to remove prior applications of NewGlass2, rinse off surface as soon as it has been scrubbed. Failure to rinse immediately will allow NewGlass2 to reattach itself to the surface. 

Application of NewGlass2

Try to avoid applying in rainy, dusty or overly windy conditions. Surfaces should be clean and dry. Using the supplied applicator, lay the NewGlass2 on the surface much like you would varnish or paint. Do not press down on the applicator as this will create bubbles and runs. Do not overload the applicator. Drips and runs need to be removed with the applicator before they can dry. Drying time is approximately 1 minute at 75 F.

Work in a 4' by 6' area laying on NewGlass2 in thin overlapping strokes. Make sure that surface is dry before applying additional coats. Apply a minimum of 5 coats. The first 2 coats may appear streaked or spotty due to absorption into the gelcoat. Coats 3 thru 5 will add shine and a self leveling sealant to protect the fiberglass. As a rule, when I can see myself in the dried surface; it is time to move to the next section. Any overlapping will disappear in 24 to 48 hours.

IMPORTANT
Please do not apply NewGlass2 if temperature will drop below 40 degrees within 24 hours following application. Do not allow NewGlass2 to freeze.

Applicators

The applicator is an artificial chamois cloth that has been fitted around a non-absorbent foam core. The slit in the core will readily allow the applicator to be slipped over your fingers for better control and feel during application. Light thin coats are required for a uniform, high shine finish. The applicator and cloth should be washed in clean water after use. If the applicator edges become hard or stiff during application, wash with clean water and wring out excess moisture. The applicator can be stored in a zip lock for future use. 

Maintenance of NewGlass2

NewGlass2 is an extraordinary product. It will not wash off or be affected by soap and water. A mild boat soap will keep your boat shiny and clean. To maintain a shine for more than 12 months, reapply 2 or 3 coats of NewGlass2 at the beginning or end of the season. In tropical areas reapply NewGlass2 every 8 to 10 months. To reapply, make sure surfaces are clean and dry. Scratches and wear areas can be touched up by applying several coats of NewGlass2. Avoid the use of ammonia based cleaners, degreasers and teak cleaners.

Removal of NewGlass2

Rubbing compound will not remove NewGlass2. Use our PreTreat to remove NewGlass2. NewGlass2 PreTreat can be mixed 3 parts water to 1 part PreTreat. It should be applied to a wet 4 by 6 area and scrubbed with the supplied scrubber. If PreTreat is being used to remove prior applications of NewGlass2, rinse off surface as soon as it has been scrubbed. Failure to scrub and rinse immediately will allow NewGlass2 to reattach itself to the surface. 

If you have any questions Please call Thom or Jennifer at 800 785 7675

© New Glass 2, All Rights Reserved Worldwide.
home | online store | shopping cart | checkout
customer accounts | contact us | mail list
store policies | terms of use | privacy statement

Site Design By:
LanBlue, inc
Kryptronic Internet Software Solutions